Welch Allyn PROPAQ CS Manuel de service Page 16
- Page / 142
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
12 Overview Welch Allyn Propaq CS Vital Signs Monitor
Network Monitor screen (2.4 GHz radio card)
To access this screen, from the Network Status screen press NETORK MONITOR.
(Or from the Main Menu, press SETUP > MORE > MORE > SERVICE > YES > MORE >
MORE > RADIO STATUS > NETWORK MONITOR.)
Network Status screen (5 GHz radio card)
To access this screen, from the Main Menu press SETUP > MORE > MORE > SERVICE >
YES > MORE > MORE > RADIO.
0
NETWORK MONITOR
BR
TEMP
100.4
98.6
1.8
97
( 15)
mmHg
(M)
25
9
S
D
NIBP
( 85)
mmHg
(M)
%
F
122
58
MCO2
S
p
O2
mmHg
38
Br/m
S
D
NETWORK
STATUS
T1
T2
ΔT
PREVIOUS
MENU
BATTERY: 9.2 VOLTS
12
TX PACKETS:
RX PACKETS:
TX RETRIES:
RX CRC ERRS:
LOAD LEVELING:
AP DROPPED MUS:
DIR
58833
49431
1MBPS
17065
1714
2
3
UNDIR
813
4604
2MBPS
34997
240
ERRORS
0
1954
PERCENT
4
2
LOW RSSI: 1
Note
Before the monitor has made a connection to the network, the fields in the above
screen will not be populated. Once the fields are populated, they will not be
updated until the monitor’s power is cycled.
Note
There is no 5 GHz Network Monitor service screen.
NETWORK STATUS
T1
°C
PREVIOUS
MENU
BATTERY: 8.4 VOLTS
FIRMWARE VER:
NET NAME:
MONITOR MAC:
MONITOR IP:
1.00.00 A0023
pco|99
00:1A:FA:00:01:02
172.29.51.32
37.0
- Vital Signs Monitor 1
- Contents 3
- Safety summary 5
- Definitions 7
- Evaluated to CSA 601-1 8
- Overview 9
- Warranty service 10
- Technical support services 10
- Recommended service intervals 10
- Monitor controls 13
- Self test and service menus 13
- Service test screens 15
- Functional verification 17
- Required equipment 18
- Safety tests 19
- RIBBED (+) SMOOTH (-) 22
- System tests 23
- Part 1— Visual check 26
- ECG X1000 27
- SYNC OUT 28
- (scope probe) 28
- DEFIB SYNC 28
- 10:42:17 30
- Temperature 31
- Nurse Call 31
- Sensor compatibility 32
- Printer tests 33
- verification preparation 34
- Example 2 35
- (continued) 37
- Mainstream CO 38
- Sidestream CO 40
- verification procedure 40
- ON NETWORK 43
- ARE YOU SURE? 45
- Calibration 47
- Equipment needed 48
- Service Manual Calibration 45 49
- Recharger supply adjustments 50
- Main power supply adjustments 52
- 8. Disconnect the DMM leads 53
- Calibrating realtime ECG out 54
- Invasive Blood Pressure 57
- MSP Board (MCO 58
- ) calibration 58
- Troubleshooting 59
- Non-recoverable error codes 60
- Battery capacity check 61
- Repair procedures 63
- Required tools 64
- Propaq CS Monitor options 65
- Front chassis 66
- Interface chassis 67
- Rear chassis 67
- Replacing the battery pack 68
- Within the European Union 69
- Outside the European Union 69
- Monitor cable 70
- Battery pack 70
- Battery pack cable 70
- Battery pack cover 70
- Opening the monitor 72
- P1 removal 74
- Closing the monitor 76
- Replacing the Analog Board 77
- Replacing the Display 79
- IMPORTANT: 80
- Short screw 80
- Reinstalling the Display 81
- Replacing air tubing 83
- Replacing cables 84
- Replacing PROMs 84
- Cuff fittings 86
- Replacing the Recharger Board 87
- Replacing the pump 89
- Replacing the side panels 90
- Removing the left side panel 91
- Installing side panels 91
- ROUTE CABLE BUNDLE 92
- ALONG BOTTOM OF 92
- REAR CHASSIS 92
- Closing Expansion Module 96
- Replacing the printer 99
- Installing the printer 100
- Opening the SpO 101
- Replacing the SpO 102
- Replacing the MSP/SpO 103
- Replacing the Sidestream CO 104
- Water Trap Receiver 105
- Exhaust Port Hole 105
- Pneumatic Reservoir 105
- Replacing the radio card 107
- Technical overview 109
- Monitor options 110
- Expansion Module 111
- Option 221 111
- SYSTEM BLOCK 114
- Power electronics description 115
- RECHARGER 116
- DIGITAL BOARD 116
- ANALOG BOARD 116
- MONITORING ELECTRONICS 117
- SYSTEM DIAGRAM 117
- NIBP pneumatics description 120
- Cabling diagrams 124
- MOT (0..5) AD (0..7) 126
- Pulse oximetry option (SpO 127
- ) description 127
- PULSE OXIMETRY BLOCK DIAGRAM 129
- Capnography (CO 130
- Mainstream Board 131
- IPC expansion 132
- Power distribution system 132
- analysis chamber (bench) 132
- Special service tools 137
- Manufacturable test equipment 139
- 810-0696-56 141
- 810-0696-57 142
© 2020, manymanuals.fr. Tous droits réservés | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels